![raspberry pi aeon labs z-stick raspberry pi aeon labs z-stick](https://i.ebayimg.com/images/g/oXUAAOSw0hlZNdNy/s-l400.jpg)
- #RASPBERRY PI AEON LABS Z STICK HOW TO#
- #RASPBERRY PI AEON LABS Z STICK MANUAL#
- #RASPBERRY PI AEON LABS Z STICK FULL#
- #RASPBERRY PI AEON LABS Z STICK SOFTWARE#
- #RASPBERRY PI AEON LABS Z STICK PC#
#RASPBERRY PI AEON LABS Z STICK SOFTWARE#
You'll need to refer to your third party software instructions if you are unsure where the function is located in software. Find the "Reset Z-Wave controller" option in your third party software and activate it.
#RASPBERRY PI AEON LABS Z STICK PC#
The third party software must take control of Z-Stick USB adapter while the Z-Stick is plugged into a PC USB port. Homeseer, Domoticz, Indigo, Axial, OpenHAB, Home Assisant, Jeedom, etc). Z-Stick also can be reset to the factory defaults settings though a third party software (ie. Using a third party software to factory reset
![raspberry pi aeon labs z-stick raspberry pi aeon labs z-stick](https://shop.swiss-domotique.ch/2749-large_default/aeon-labs-controller-usb-z-wave-plus-z-stick-zw090c-gen5.jpg)
#RASPBERRY PI AEON LABS Z STICK MANUAL#
Please consult the instruction manual of the host software to add the Z-Stick to a pre- existing Z-Wave network (i.e. This must be done through the host software which takes control of Z-Stick USB adapter while Z-Stick is in SerialAPI-Mode. This tool can also be used to transfer your old Z-Stick Gen5 network to a Z-Stick Gen5+, you can follow the steps here:
#RASPBERRY PI AEON LABS Z STICK HOW TO#
You can learn how to use Backup Software here to backup, and restore: You can download the installation setup for Backup Software here: This way you will never have to re-do your network if there are catastrophic issues. You are able to backup the Z-Stick Gen5 using our Z-Stick Gen5 Backup Software in any case you need to restore an older save of your network, or replace a failed Z-Stick Gen5. Z-Stick Gen5 and how to get started with Domoticz. We recommend free software Domoticz if you are just getting started as it is one of the easiest free softwares you can use. You can find all known third party softwares in this link:
#RASPBERRY PI AEON LABS Z STICK FULL#
In order to use the Z-Stick Gen5 and control your Z-Wave network, you must download a third party software to have full control over your software. When done, tap the button once on Z-Stick Gen5+ to bring it out of unpair/exclude mode. Repeat step 3 for any device you want to unpair if you have multiple devices that you need to exclude.Ħ. Z-Stick Gen5+ LED will confirm if it paired something successfully by showing a solid blue LED for 2 seconds before returning to a fast blinking Amber color LED.ĥ.hold for 2 seconds and release, triple tap, double tap, etc). Typically the button press on the Z-Wave device is a single tap, but some have special button presses (ie. Follow the instruction of the Z-Wave device that you want to unpair. Do not use in damp, moist, and / or wet locations.Ĥ. Z-Stick Gen5 is intended for indoor use in dry locations only. Improper battery use may damage the product. Keep product and batteries away from open flames and extreme heat. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. Please read this and other device guides carefully. There are subtle differences between Z-Stick Gen5+ and Z-Stick Gen5, you can learn more by reading the table at this page: Indicates that Z-Stick Gen5 has communicated a Z-Wave command. Will only reset if RESET button is held for a full 20 seconds (followed by the confirmation LED indicator).įactory reset does not happen if released earlier than 20 seconds.Ĭonfirmation of success/communication for pair, unpair, or factory reset. Indicates that it has entered factory reset mode. The technical specifications of Z-Stick Gen5+ can be viewed at that link. This includes Raspberry Pi 4 compatibility, and native Z-Wave SmartStart and Z-Wave S2 compatibilities.
![raspberry pi aeon labs z-stick raspberry pi aeon labs z-stick](https://cdn.stamped.io/tr:h-800,/uploads/photos/89063_1534623318071_9ecbca3d_32be_4773_a1a4_bcd08277e424.jpg)
Z-Stick Gen5+ offers compatibility with newer technologies than non +/plus, standard Z-Stick Gen5. Z-Stick Gen5+ (ZW090) Z-Stick Gen5+ user guide